Tico 772/773/774 Time Counter - Hengstler

Series produk ini benar-benar multitalenta, memiliki hingga tiga preset dan dapat dihubungkan menggunakan konektor plug-and-play. Produk memungkinkan penghitungan dengan frekuensi sangat tinggi hingga 60 kilohertz dan secara universal cocok untuk digunakan sebagai penghitung denyut nadi, takometer, pengatur waktu, penggeser bergeser atau pencacah batch. Tampilan 6-warna multi-warna yang besar backlit dan mudah dibaca. Fleksibilitas tingkat pemrograman yang ditawarkan oleh penghitung multifungsi ini memungkinkannya digunakan sebagai penghitung waktu dan, jika diperlukan, dengan banyak fungsi yang dapat diprogram. Fungsionalitas tambahan yang ditawarkan oleh Interface RS232 memfasilitasi pemrograman yang cepat dan mudah pada PC dan memungkinkan perangkat untuk berkomunikasi dengan komputer.

• Operasi yang sangat sederhana
• Empat warna lampu latar yang berbeda
• Layar besar dan mudah dibaca
• Menghitung frekuensi hingga 60 kHz
• Tiga preset
• Prescaler 0,0001 - 99,9999
• Interface RS232 (Tico 774)
• USB Interface (Tico 773)
• Asisten pemrograman (Windows XP 32 bit, Windows Vista 32 bit, Windows 7 32 bit)(Tico 773 & 774)

Specification

General

Jenis Produk	tico 772	tico 773	tico 774
Fungsi	Time counter
Teknologi	Electronic
Digits	6-digit
Display	6-digit
	2-line
	counting display/presets
	leading zero suppression
	decimal point (up to 4 places)
Preset	3 presets
Interface	-	USB-interface	RS232-interface
Tingg Digit [mm]	1. Line 9.3 mm (0.4 in)
	2. Line 7.2 mm (0.3 in)
Display Variant	reflective LCD
	transflective positive LCD, black digits, backlit
	transmissive negative LCD, white digits, red or green backlit, background black
View Angle	12:00
Relay	1 or 2 relays

Electrical

Voltage	12-30 VDC
	24-240 VAC
Reset	manual reset
	electrical reset
	automatic reset
Signal Times	0.01 s to 599.99 s or bistable, programmable, tolerance + 10 ms, active on/off
Current Consumption [mA]	< 200 mA at 12 - 30 VDC reflective
	< 250 mA at 12 - 30 VDC with Backlight
	< 250 mA at 24 VAC
	< 50 mA at 115, 230 VAC
	< 80 mA at 100 - 240 VAC switching power supply
Power Consumption	5 W <8 td="" w="">
Cable Cross-Section	1...1.5 mm² (0.0015...0.0023 in²) with multicore cable end
Input Resistance	approx. 10 kOhm
Pulse Length min.	17 ms (30 Hz), 8 µs (60 kHz)
Supply Voltage	12-30 VDC
	24, 115, 230 VAC
	100-240 VAC
Count Frequency [Hz]	max. 60 kHz (TTL 20 kHz): Single-channel counting and directional input
	max. 60 kHz (TTL 20 kHz): differential or totalizing operation
	channel (A+B together)
	max. 30 kHz (TTL 20 kHz): phase discriminator 1- or 2-fold evaluation
	max. 15 kHz (TTL 15 kHz): phase discriminator 4-fold evaluation
	attenuated 30 Hz
	For further details, see graphic and manual.
Overload Protection	ext. backup
	DC: 0.16 AT (IEC 127), DC: 0.2 AT (UL 198)
	24 VAC: 315 mAT
	115 VAC: 63 mAT
	230 VAC: 32 mAT
	100-240 VAC 630 mAT
Overload Protection Relay Output	ext. backup 230 V
	2.5 A mT
Sensor Supply	transformer power supply: 12-24 VDC (load-dependent)
	max. 50 mA
	switch power supply24 VDC -5%
	max. 115 mA, max. capacitative load 470 µF
Storage of Values	NVM> 10 years
Electrical Connection	pluggable screw terminals / connecting clamps
Amplitude Threshold	< 2 V and > 8 V or < 1 V and < 4 V at TTL levels
	amplitude max. 40 VDC
Active Edge	programmable, positive with PNP input, negative with NPN input
Pulse Shape	any square wave (1:1 for max. frequency)
Prescaler	0.0001 - 99.9999
Set Function	set to VW 0 (independent of resets)
Display and Preset Range	- 999 999 to + 999 999
Alarm Signal	display blinks
	when presets 0,1 or 2 are active
Relay (Preset 1 and 2)	Varistor max. 250 VAC / 30 VDC / 5 A
	Varistor min. 5 VAC / 5 VDC / 10 mA
	Delay < 10 ms
Transistor output (Preset 1 + 2)	DC supply: PNP output 12 - 30 VDC, max. 50 mA
	transformer performance (24, 115, 230 VAC): PNP output 12 - 24 VDC, max. 30 mA
	switch power supply 100-240 VAC: PNP output 24 VDC, max. 50 mA
Application Output	DC supply: PNP output 12 - 30 VDC, max. 20 mA
	transformer performance (24, 115, 230 VAC): PNP output 12 - 24 VDC, max. 20 mA
	switch power supply 100-240 VAC: PNP output 24 VDC, max. 20 mA
Attention	Only for transformers (24, 115, m230 VAC:
	The energy load on the outputs (sensors 12-24 VDC, out1, out2, Appl.-Outp.) may not be more than 65 mA total.

Counter

Counter Mode Input A,B	Single channel add or sub, directional input,
	differential operation add / sub, totalizing operation add / add,
	phase discriminator 1-, 2- or 4-fold evaluation
Preselect Modes	absolute or trailing preset
	range signal/value limit (Sign. 1 < VW1)
	Sign. 2 < VW2
Application Input/Output (Counter)	Output: prescaler-out
	preset 0-out
	direction-out
	input: additional counter input add / sub
	reset
	set
	gate
	keylock
	hold
	teach in
Mode	batch counter with preset or 2. totalizing counter with preset
Count Mode	differential operation add/sub
	totalizing operation add/add

Tachometer

Measuring Principle (tachometer)	period measurement (1/tau)
Display Range	1/min or 1/sec
min. Frequency	1 Hz or 0.1 Hz
Limit Values	2 alarms with programmable start suppression
	+ 1 additional upper limit on the application input
Tachometer Mode of Operation	Single channel add or sub, directional input,
	differential operation add / sub, totalizing operation add / add,
	phase discriminator 1-, 2- or 4-fold evaluation
	A / B or (A-B) / A %
Application Input/Output (Tachometer)	Output: preset 0-out
	direction out
	input: additional counter input add / sub
	gate
	keylock
	hold
	teach in
Accuracy of the Tachometer Function	Time base: ± 30 ppm
	Measuring principle: cycle duration measurement
	Measuring time: min. 0.5s / max. 1s or 10s
	Measuring resolution: 0,4 µs <30 p="" ppm="">
	Display resolution: 4 decimal points
	1 digit = 100 ppm
Overall Tolerance (Tachometer)	= display resolution + tolerance time base = 130 ppm

Time Counter

Time Base (Tachometer)	programmable, sec
	min
	h or hh.mm.ss
Measuring Principle (timer)	pulse width or period duration measurement (start-stop)
	start Inp. A + Stop Inp. B,
	Start/Stop button
Function Time Counter	single pulse measurement or cumulative measurement
Application Input/Output (Timer)	Output: preset 0-out
	input: additional Run
	Stop
	Reset
	Set
	Keylock
	Teach in
Accuracy of the Timer	Time base. ± 30 ppm
	Start / Stop time point: 16 µs / 16 ms (unattenuated / attenuated)
	resolution: 100 µs = 100 ppm
Overall Tolerance (Timer)	= display resolution + tolerance time base = 130 ppm
Resolution	1, 0.1, 0.01, 0.001, 0.0001

Environment and security

IP Protection Class	IP 65
Operating Temperature [°C]	0 …... + 50 °C (+ 32 ... 122 °F) EN 60 068-2-1/2
Storage Temperature [°C]	- 20 ... + 65 °C (- 4 ... + 149 °F) EN 60 068-2-1/2
Degree of Protection	IP 65 front, EN 60529
	IP 20 connections
Cable Length	* An additional protective circuit is required when using cables longer than 30 m
	which are connected to a DC power supply at TTL input levels
General Design	EN 61 010-1 / IEC 61010-1
EMC - Interference immunity	EN 61326-1 Industrial**
EMV-Emission	EN 61326-1 Class B*
Approvals	UL
	CSA File-Nr. E 338588
Vibration Resistance	10 m/s² (33 ft/s²) (10 . 150 Hz), EN 60 068-2-6
Shock Resistance	100 m/s2 (328 ft/s2) (18 ms) acc.IEC 068-2-27
Protection Class	II, EN 61010-1 / IEC 61010-1
Contamination Level	V 2
	EN 50178
Climate	40°C (104 °F)/ 93% RH class 4K4H
	EN 60 068-2-78
	25 - 50°C (122 °C) / 93% RH
	cyclic
	EN 60 068-2-38
	elevations up to 2000 m (6561 ft)
Resistence to Chemicals	front film acc. DIN 42 115-2
RoHS	compliant

Mechanical

Size [mm]	48x48x118
Mounting Options	Clamping frame
Mounting	with clamping frame
Reset	manual reset using keypad
	external reset static or dynamic
	pulse duration min. 5 ms
	automatic reset after preset 2 has been reached
	no loss of pulse at the maximum counting frequency due to automatic resetting. programmable using application input and power-up reset
Weight [g]	approx. 200 g (3.2 oz)
Dimensions [mm]	48 mm x 48 mm x 118 mm (1.9x1.9x4.6 in), installation depth 110 mm (4.4 in), DIN 43 700
Panel Thickness [mm]	max. 11 mm