Resistance Thermometer TP 62 Hengesbach

The QUICKTEMP TP62 temperature sensor has 2 transmitters in the connection head, which may, for example, be used for indication and registration purposes. In addition, QA tests, repair and maintenance work are possible without having to interrupt the process and open the measuring point. The entire device, including the connection head and measuring insert can be taken out of the process without loosening the electrical cables. This saves time and resources and creates process security.

The measuring insert is a double PT100 sensor with spring bearings and metallic contacts to ensure good heat transmission and short response times. The design of the Quicktemp system is based on one basic device with various fitting lengths or process connections, assuming defined fitting lengths. For the user, this guarantees a high degree of flexibility, while at the same time minimising the storage costs.

The two standard TE42 transmitters installed have an mA output and can be programmed via the set-up plug. The connection head in the PA is robust and resistant to external environmental conditions (protection class IP 66); it ensures good access, including the cabling of the transmitters.

Features:

• double transmitter (4-20 ma or hard output with 2-wire technology)
• quality assurance tests and retooling without process interruption and without loosening the electrical wiring.
• exchangeable measuring insert with spring bearings and metallic contact.
• various designs for appropriate installation, adaptation to existing measuring points without design changes.
• quick response times due to tapered sensor tips

Specification:

General details
Device type/measuring principle	TP62...T500 / Pt100 resistor
Measuring insert
Sensor type	- 2x Pt100 in accordance with EN 60751, 3-wire
Version	- Standard version tmax=400°C
	- Mineral-insulated version tmax=600°C, vibration resistant
Dimensions	Length 154mm (with T500), Ø=3mm
Output
Version	- Temperature transmitter - 2X TE42, 4...20mA, 2-wire (standard)
Transmitter TE42
Supply voltage	10 to 35 VDC	Temperature drift	≤ ± 0.01%
Current requirement	≤ 3.5mA	Calibration temperature	+25°C ± 5K
Current limitation	≤ 23mA	Ambient temperature	-40...+85°C
Switch-on delay	4s	Configurable start of range	< 50% final value
Response time	1s	Attenuation	0...60s, configurable
Fault signal	≤3.6mA / ≥21mA, configurable	Vibration resistance	4g / 2...150Hz (according to IEC
			60068-2-30)
Voltage change influence	≤ ± 0.01%/V of 24V FS	Protection class	IP00 (installed, see housing protection
			class)
Circuit type	2-wire	Climate class	Cl. C, EN60654-1
Output signal	4...20mA or 20...4mA, 2-wire	CE conformity	EN 61326-1
Load resistance	(Vref-10V)/0.022A	Measuring accuracy (typical	0.2K or 0.08%
		values)
Long-term stability	≤ ± 0.1K/year (under reference condi-	Measuring current at sensor	< 0.6mA
	tions)	(normal)
Linearity error	≤ ± 0.1%/K	max. sensor cable resistance	11Ω/wire
Burden influence	≤ ± 0.02%/100Ω FS	Wire compensation with 2-L
Measuring range	Type	Pt100, 2L / 3L / 4L	min. temperature	-200°C
	min. temperature span	10K	max. temperature	+650°C
Connecting terminals	Screw clamps (captive screws), wires up to 1.75mm² or 1.5mm² with wire-end ferrules
Measuring accuracy
Pt100 class in accordance with EN 60751	- A (Standard)
	- AA (1/3B)
Response times	T50≤4…6sec or shorter (design-dependent), other information on request
Conditions of use
Medium temperature	-50...400°C (standard), -50...600°C (version with mineral-insulated measuring insert)
Ambient / storage conditions	- -40...+85°C (increased risk of cable breaks at less than -20°C)
- Humidity 95%, without condensing (depending on transmitter used)
Protection class acc. to EN60529   IP 67 and IP 69K (depending on design)
Structural design - basic device
Electrical connection	Round plug-in connector M12x1, 4-pin, nickel-plated brass (stainless steel available on request)
Process connection	Quicktemp with screw-in thread G¼“ - for protective sleeves with collar and loose union nut G¼“
Seal	Captive O-Ring seal
Materials	- Field housing / lid:	CrNiSt 1.4301 (304)
	- Housing seal:	FPM (Viton®)
	- Measuring insert:	CrNiSt 1.4571
	- O-Ring seal:	FKM
Structural design - protective	sleeves
Process connection	- Clamp connection
	- Weld-in solutions
	- Conical coupling / threaded coupling DIN 11851
	- Female union / threaded coupling DIN 11864-1
	- VARIVENT® type N, type F
	- 1“ ISO 228 thread
	- Other connections such as elastomer-free sealing systems, Ingold connectors, 1“ ISO 228 thread, ...
Materials	- Sleeve body and collar CrNiSt 1.4404
	- Union nut CrNiSt 1.4305
Shape of tip	- Standard
	- Tapered
Max. process pressure	Depending on design, min. PN10 (optionally up to PN80, pay attention to design)
Accessories for Quicktemp TP62...T500
Configuration kit	TZ42-USB with HengCom software (as download at www.hengesbach.com)
Certificates	Calibration certificate, conformity declaration, material products in accordance with EN 10204

Download Data Sheet:Resistance Thermometer TP 62

Ref: Hengesbach.com