Bamo Turbidity Monitor BAMOPHAR 436

Bamo Turbidity Monitor BAMOPHAR 436[/caption]

Bamo Turbidity Monitor BAMOPHAR 436 | Descriptions

BAMOPHAR 436 is equipped with a color touch screen to set up the configuration and to display the turbidity, temperature and state of thresholds. Copies of measurement are available on 2 outputs 4-20 mA. BAMOPHAR 436 displays the turbidity value measured by one of our transmitters, to respond to process requirements.

• TURBICUBE in PVC or PPH and TRUBOMAT GAB in stainless steel, are dedicated to in-line measurement
• TURBISENS in PVC is an immersion probe with transmitter for measurements in tanks, basins, channels

A complete measuring system includes:

• One monitor BAMOPHAR 436
• One turbidity transmitter

OPTION: Extension terminal for a second parameter

• Allows a second measurement (pH, Flow rate, Conductivity, etc.) (Configuration and display on the main unit)
• Connected to main unit with 2 x 2-wire shielded cable (Cable length between both devices: max. 500 m)
• RS422 and Data Logger of main unit are shared between both units
• Wall or panel or DIN rail mounting: according to the model

Features

• Color touch screen
• Available scales: 0.001 to 9999 FNU, FAU, NTU, mg/l, g/l
• 2 outputs 0/4-20mA (measurement & T.°C)
• 3 Independent relays
• 1 Relay for alarming function
• OPTIONS: RS 422 /J-BUS + LOGGER Extension terminal for a 2nd measurement parameter

Application

Turbidity measurement for monitoring and processing water treatment:

• Monitoring of source or wells for drinkable water
• Monitoring of filtering diaphragms, ultra-pure water production units, reverse osmosis plants
• Measurements in basins, decanting process
• Monitoring of clogging and rinsing of filtering units
• Monitoring of cooling towers
• Control of wastewater before discharge

Specification

End-user interface	Color touch screen 4.3'', resolution 480x272 pixels
	Display of measurements, menus, temperature, relay status
	Configuration - Keyword protected
Measuring scales	To set up according the turbidity transmitter in use (from 0.001 to 9999 FNU, FAU, NTU, mg/l, g/l)
Sensor signal input	For Turbidity transmitter 4-20 mA, 2-wire or 4-wire technique
Temperature display	Input signal for Pt 100 Ω 3-wire sensor, within the range 0 to 100 °C Or manually set up of operating temperature.
Relay outputs Configurable thresholds	4 contacts N.O., potential free
Configurable thresholds	2 Independent thresholds, for measurement or temperature
	1 Independent threshold, for measurement or temperature or to external function
	1 threshold for alarming function (Temperature sensor fault) or measurement out of range
Contact Initial resistance	100 mΩ max. (voltage drop 6 V DC 1 A)
Switching power	831VAAC/3A/277VAC
	90W/3A/30VDC
Switching capacity (min.)	100 mA, 5 V DC (variable according to switching frequency, environmental conditions and accuracy).
Measurement output	0/4-20 mA (max. 600 Ω) proportional to measurement 0/4-20 mA (max. 600 Ω)
Temperature output	range 0 to 100 °C
Main power	230 V - 50/60 Hz (others on request) - Consumption 10 VA
supply Models	Panel mounting, 96x144 mm; Front IP65; Rear IP4, screw terminals
Storage	Wall mounting, IP65, cable glands -10 ... +70 °C
Operating temperature	-5 ... +50 °C
Interface	RS422 output, J-BUS link - Binary slave mode - 2400 to 9600 bauds
	Data Logger; Record of cycle average measurement - 150 000 records max. on memory

Ref: bamo.eu

Contact us : sales@wmablog.com or visit to our E-Commerce

Download Data Sheet: Turbidity Monitor BAMOPHAR 436