Intrinsically Safe Supply Units, Dinel-Level and Flow Measurement

 

 INTRINSICALLY SAFE SUPPLY UNITS

Supply and switching units NxxU are used for energizing of NAMUR output sensors (DLS–27Xi, CPS–24Xi, etc.) located in hazardous explosive areas. Due to the state of the connected sensor, they switch their output changeover relay contact or a transistor switch. Moreover, they can provide a simple 2-state level regulation (pump-up and pump-down control).

Features

• For energizing and state-detection of NAMUR sensors (EN 60947-5-6)
• The connected sensor can be located in hazardous explosive areas up to zone 0
• Relay or transistors output
• High-frequency switching (up to 2kHz – ver. "T")
• LED state indication
• Power supply 230 V AC or 24 V DC
• Mounting on DIN rail 35 mm

Features of Variants

• NSSU – 811 Single channel unit without additional functions for supply and state detection of one NAMUR sensor. Output invariant "T" (transistor switch) or "R" (relay contact).
• NSSU – 812 Single channel unit with LFD* system for supply and state-detection of one NAMUR sensor. Output invariant "R" (relay contact).
• NDSU – 822 Dual channel unit without additional functions for supply and state detection of two NAMUR sensors. Output invariant "T" (transistor switch) or "R" (relay contact).
• NLCU – 821 2-state level regulation unit using two connected limits NAMUR sensors. Output invariant "R" (relay contact).
• NLCU – 822 2-state level regulation unit with LFD* system using two connected NAMUR sensors, protection against non-logical states of level sensors. Output invariant "R" (relay contact).

Another Article: Flux Pump Kits for Acids Flux Pump Kits for Alkalis Flux Container Pumps MINIFLUX Flux Drum Pumps, Barrel Pumps and Container Pumps Flux Centrifugal Immersion Pumps

Specification

	NSSU–811	NSSU–812	NDSU–822	NLCU–821	NLCU–822
Number of connectable sensors	1	1	2	2	2
Failure signalization (LFD system)	NO	YES	NO	NO	YES
Nominal supply voltage
Version 230 V	30 ... 230 V AC/DC (+10%) 50 ÷ 60 Hz
Version 24 V	10 ... 30 V AC (+10%) 50 ÷ 60 Hz; 10 ... 40 V DC (+10%)
Nominal power demand (AC / DC)	4 VA / 4 W
Output open – Circuit voltage	9.2 V DC
Output current – Treshold	1.55 mA (± 0.1 mA)
Current limits for LFD system	-	< 0.1 mA	-	-	< 0.1 mA
	-	> 6 mA	-	-	> 6 mA
Allowable short-circuit time in input terminals	Unlimited
Limit parameters	V; I0 = 10.4 mA; P0 = 27.3 mW; C0 = 1.8 μF; L0 = 150 mH
Safe isolation voltage Um (term. 9 - 16)	253 V
Contact voltage drop (output transistor is closed)	2 V (Variant "T)
Dynamic parameters * (Triggering / Gap pulse)
Variant "R"	Min. 50 ms	-	Min. 50 ms	-	-
Variant "T"	Min. 250 μs	-	Min. 250 μs	-	-
Max. switching frequency (Max. load / Without load)
Variant "R"	0.1 Hz / 10 Hz
Variant "T"	2 kHz / 2 kHz
Output characteristic (Variant "R")
Version 230 V	250 V AC / 2 A / 100 VA; 250 V DC / 2 A / 50 W
Version 24 V	40 V AC / 2 A / 80 VA; 40 V DC / 2 A / 80 W
Output characteristic (Variant "T")	40 V / 50 Ma	-	40 V / 50 mA		-
Relay contact life (Variant "R")	Min. 30 x 106
Ambient temperature	-20°C ... +60°C
Protection	IP20
Housing material	Polylcarbonate
Material of terminals	CuBe
Max. conductor size	1 x 2.5 mm2
Isolating voltage (mains terminal / output)	3500 V
Weight Approx.	0.2 kg
* Dynamic parameters are valid by connection to contact on input unit (impulse transmitting from gas-meter, etc.)

Download Catalog: INTRINSICALLY SAFE SUPPLY UNITS,Dinel-Level and Flow Measurement

Ref: Dinel.cz